News Articles Archives - Heat Treating Society

One Minute Mentor: Mechanical Shock

asmeditor — Wed, 04 Mar 2026 02:59:48 +0000

Mechanical shock is sometimes used to stabilize tool steels. One method of producing shock is to suspend the part so that it hangs freely and then strike it with a wooden hammer. This is believed to set up elastic waves which add to the magnitude of the residual stress imparted by the previous heat treatment. At locations where the resultant magnitude of stress exceeds the elastic limit, plastic flow should occur and result in stress relief. This would be manifest by higher dimensional stability. A shock treatment should not be considered as a substitute for a thermal method of stabilization but rather as an auxiliary method which enhances stabilization.

Dimensional changes in W1 steel resulting from dropping on a concrete floor as determined by Fletcher (are shown in Fig. 6. The untempered specimens showed greater dimensional changes than the tempered specimens due to the higher level of residual stress in the untempered condition.

For more information, click on the link below (subscription required). Then scroll to Figure 6.

Jon L. Dossett; George E. Totten, *Control of Distortion in Tool Steels*, ASM International, 2014
https://doi.org/10.31399/asm.hb.v04d.9781627081689

The post One Minute Mentor: Mechanical Shock appeared first on Heat Treating Society.

Ipsen USA Receives New Vacuum Furnace Order from Urschel Laboratories

asmeditor — Wed, 04 Mar 2026 02:58:12 +0000

Ipsen USA, Cherry Valley, Illinois, announced a new equipment order from Urschel Laboratories for a MetalMaster HR 54×48 vacuum furnace. The order marks 40 years of partnership between the two companies, with the new unit replacing an original Ipsen furnace installed in 1986.

The MetalMaster HR is designed for high-performance heat treating applications including hardening, tempering, brazing, and annealing in a vacuum or partial-pressure environment. The furnace features a horizontal front-loading design with an integrated high-pressure gas quench system.

Urschel Laboratories, based in Chesterton, Indiana, is a global manufacturer of precision food cutting equipment. The company relies on vacuum heat treatment to achieve the hardness, wear resistance, and dimensional stability required for its cutting components, which operate under demanding production conditions in the food processing industry.

The replacement of the 1986 furnace reflects both the longevity of Ipsen equipment and the ongoing need for modern controls, energy efficiency, and process documentation capabilities in today’s manufacturing environment. Ipsen reported a 45% year-over-year increase in new equipment units sold in 2025.

Read further here

The post Ipsen USA Receives New Vacuum Furnace Order from Urschel Laboratories appeared first on Heat Treating Society.

Seco/Warwick Partners with European Defense Sector Manufacturer

asmeditor — Wed, 04 Mar 2026 02:56:26 +0000

Seco/Warwick, Swiebodzin, Poland, announced its first contract with a European defense manufacturer. The company will deliver a customized single-chamber vacuum furnace equipped with advanced low-pressure carburizing technology and high-pressure gas quenching for heat treatment of steels used in firearm manufacturing.

The contract represents a shift by the defense client from traditional gas carburizing to modern low-pressure carburizing, which improves quality, process predictability, and energy efficiency. The vacuum furnace approach eliminates the environmental concerns associated with atmosphere-based systems while delivering more uniform case depth and reduced distortion.

The deal holds strategic significance for both parties. For the client, it represents a modernization of defense manufacturing infrastructure. For Seco/Warwick, it establishes a position as a solutions provider in the European defense sector, a market segment with growing demand for advanced thermal processing equipment.

Seco/Warwick operates globally with manufacturing facilities in Poland, the United States, India, and China, and service centers across Europe and Asia.

Read further here

The post Seco/Warwick Partners with European Defense Sector Manufacturer appeared first on Heat Treating Society.

Gasbarre and SOLO Swiss Announce Exclusive Licensing Agreement for North America

asmeditor — Wed, 04 Mar 2026 02:54:50 +0000

Gasbarre Thermal Processing Systems, DuBois, Pennsylvania, and SOLO Swiss SA, Porrentruy, Switzerland, announced an exclusive licensing agreement granting Gasbarre the rights to promote, sell, and manufacture the SOLO ProfiTherm heat treating system in North America. The agreement was announced on January 21, 2026.

The ProfiTherm system features a modular arrangement of bell furnaces and quench tanks with direct, rapid transfer from furnace to quench. The design is positioned as a practical alternative to traditional integral quench batch furnaces, offering a more compact footprint that simplifies installation and reduces plant disruption.

ProfiTherm supports a range of heat treating processes including austempering, marquenching, carburizing, carbonitriding, and neutral hardening. Target applications include captive heat treat departments and commercial shops serving general industry, aerospace, defense, and bearing markets.

The partnership expands Gasbarre’s equipment portfolio and gives North American heat treaters access to SOLO Swiss bell furnace technology that has been widely adopted in Europe.

Read further here

The post Gasbarre and SOLO Swiss Announce Exclusive Licensing Agreement for North America appeared first on Heat Treating Society.

Bodycote Expands U.S. Aerospace and Defense Footprint with Acquisition of Spectrum Thermal Processing

asmeditor — Wed, 04 Mar 2026 02:52:33 +0000

Bodycote, Macclesfield, UK, announced the acquisition of Spectrum Thermal Processing, a heat treatment provider based in Cranston, Rhode Island. The transaction closed on January 14, 2026.

Spectrum brings established Nadcap-accredited and ITAR-compliant capabilities to Bodycote’s North American operations, including vacuum heat treatment, low-pressure carburizing, and gas nitriding services. The acquisition strengthens Bodycote’s regional capacity in the northeastern United States and reinforces its ability to support aerospace, defense, space, and industrial customers.

The deal expands Bodycote’s presence in critical process categories that serve sectors with demanding quality and compliance requirements. With the addition of Spectrum’s facility and expertise, Bodycote continues to build on its position as the world’s largest provider of heat treatment and specialist thermal processing services.

Bodycote operates more than 160 facilities in 22 countries worldwide. The company noted that the acquisition aligns with its strategy of targeted growth in markets with high barriers to entry and strong long-term demand, particularly in the aerospace and defense sectors.

Read further here

The post Bodycote Expands U.S. Aerospace and Defense Footprint with Acquisition of Spectrum Thermal Processing appeared first on Heat Treating Society.

One Minute Mentor: Advantages and Limitations of Heat Treatment Simulation

Vineeth Venugopal — Thu, 03 Apr 2025 15:34:09 +0000

Heat treatment simulation can be a tool for optimization of heat-treatment processes, but at the present this method is still limited. Therefore most HTS is based on rough simplifications of the process. Simplifications can involve the process, number of phases, transformation kinetics, continuums models instead of micro-mechanical models, etc. These simplifications also result in inaccuracies in the calculations.

For more information, click on the link below (subscription required). Then scroll to Figure 16. R Schneider; R. Mesquita; W Schützenhöfer, Distortion in Tool Steels, ASM International, 2014 https://doi.org/10.31399/asm.hb.v04d.a0005980

The post One Minute Mentor: Advantages and Limitations of Heat Treatment Simulation appeared first on Heat Treating Society.

ECM establishes new vacuum furnace entity in mexico under MEXVAC ECM name

Vineeth Venugopal — Thu, 03 Apr 2025 15:30:51 +0000

ECM USA, Pleasant Prairie, WI, announced the official launch of its new Mexican subsidiary, ECM Mexico, operating as MEXVAC ECM, S.A. DE C.V. This development marks a significant step in expanding ECM’s presence and service capabilities within the Mexican heat treatment industry.

The ECM Mexico team is led by operations manager Juan Cruz and field service and PLC engineer José López, under the direction of Pierre-Loic Rousset and Dennis Beauchesne. The team will work closely with ECM USA to provide localized support, reflecting ECM’s long-term commitment to strengthening service infrastructure for customers across Mexico.

The new entity will serve as a dedicated supplier of vacuum furnace technologies and support services, aiming to meet growing demand in the region for high-performance thermal processing equipment.

The post ECM establishes new vacuum furnace entity in mexico under MEXVAC ECM name appeared first on Heat Treating Society.

Bodycote joins energy industries council to expand engagement with global energy sector

Vineeth Venugopal — Thu, 03 Apr 2025 15:27:46 +0000

Bodycote, Macclesfield, UK, announced its membership with the Energy Industries Council (EIC), a leading global trade association for the energy sector. This move strengthens Bodycote’s strategic alignment with the evolving needs of the industry and reinforces its role as a provider of heat treatment and specialist thermal processing services across power generation and energy infrastructure markets.

Through its membership, Bodycote gains broader access to key industry stakeholders, enabling stronger supply chain collaboration and the pursuit of new business opportunities within the energy sector. The company serves a wide range of EIC members, fostering synergies that support innovation and operational excellence.

Bodycote’s engagement with the EIC supports its commitment to sustainability, particularly in nuclear and renewable energy markets. The partnership enhances customer access to Bodycote’s services via EIC platforms and events, further promoting solutions that improve performance, efficiency, and reliability in critical energy applications.

The post Bodycote joins energy industries council to expand engagement with global energy sector appeared first on Heat Treating Society.

Pyromaitre delivers integrated heat-treating solution to GKN driveline Mexico

Vineeth Venugopal — Thu, 03 Apr 2025 15:23:12 +0000

Pyromaitre, Lévis, Québec, announced the completion of assembly for its P-208E oven system for GKN Driveline Mexico, marking a total of four systems delivered to the client. The company developed a fully integrated solution that includes a high-speed tempering furnace, a post-treatment cooling chamber, automated loading and unloading systems, and a smoke collection unit. Each component was configured to meet the customer’s specific production requirements.

Pyromaitre specializes in resolving convective heat transfer challenges with precision and efficiency. The company focuses on driving innovation and operational performance, aiming to be a recognized leader in stress relief and tempering solutions. Its core values—integrity, innovation, customer satisfaction, and teamwork—guide its approach to delivering high-performance thermal processing systems.

Read further:

The post Pyromaitre delivers integrated heat-treating solution to GKN driveline Mexico appeared first on Heat Treating Society.

Solar Atmospheres expands vacuum heat-treating capacity in Eastern Pennsylvania

Vineeth Venugopal — Thu, 03 Apr 2025 15:20:14 +0000

Solar Atmospheres, Souderton, PA, announced the commissioning of two additional 2-bar vacuum furnaces at its Eastern Pennsylvania facility. The expansion is aimed at supporting increased demand from the aerospace and industrial gas turbine industries, as well as specialized hydride/dehydride processing of reactive metals such as titanium, tantalum, and niobium.

The newly installed furnaces, manufactured by Solar Manufacturing, feature large working hot zones measuring 45 inches wide by 45 inches high by 72 inches deep. They are rated for temperatures up to 2400°F and maintain a temperature uniformity of ±10°F, meeting the stringent requirements of high-performance heat treatment applications.

Mike Moyer, vice president of sales at Solar Atmospheres, noted that the new equipment, outfitted with the latest control systems from Solar Manufacturing, enhances operational efficiency and safety. He added that this expansion supports the company’s commitment to providing reliable service, competitive pricing, and fast turnaround times to its customers.

The additional capacity reflects Solar Atmospheres’ ongoing investment in advanced thermal processing technology to meet the evolving needs of its industrial and aerospace clients.

Read further here

The post Solar Atmospheres expands vacuum heat-treating capacity in Eastern Pennsylvania appeared first on Heat Treating Society.